The handmade grille and the onepiece hood top and sides were created by Desrosier, and he fabbed a hydraulic strut that opened the hood when he pressed a button on the steering column. De e dags 19 oktober -
Scandinavian Village till USA
Bariete  is a monkey mink  who guards the gates of the Mokomo Dukedom. Bariete is a male mink who looks like a small, humanoid monkey. He wears a striped top hat and a suit.
He takes his job of guarding the Mokomo Dukedom 's gates very seriously, as demonstrated when he became angry and insulted the Straw Hats after they tried to reach Zou without permission. Like a stereotypical monkey, he loves bananas, to the point where he will accept them as a bribe.
He has a habit of saying "ete"  and finishing sentences with "degosaru". As a mink, he is a natural-born warrior and can use Electro. When the Beasts Pirates invaded Zou , an injured Bariete alerted the populace of the invaders by ringing the raid bell.
Bariete was guarding the entry gate to Mokomo Dukedom when he noticed the Straw Hat Pirates and their allies scaling Zunisha 's leg. In an attempt to prevent them from entering Zou, he jumped off and crashed into Kin'emon and Kanjuro , causing them to fall with him down to the Thousand Sunny.
The samurai and Bariete later attempted to climb to Zou using a cat created by Kanjuro's Devil Fruit powers, but the attempt failed due to the water from Zunisha's self-washing dissolving Kanjuro's drawing. The following morning, they finally reached the top of Zou, where Kin'emon asked Bariete about Raizo. First, the hardware and the product is awesome. Extremely high quality, much better than anything you'd get at a hardware store and simple.
If you were to price it out, this is a great deal. In a perfect set up, this will install very easy. As anyone who has done a project will say though, it never goes as planned.
Everyone always post when something installs easy, but not when they run into some issues. In my master bathroom I had two, 2 foot wide doors that opened into the bathroom. One door when opened blocked a sink the other the toilet. Most ridiculous design ever, pocket doors should have been installed. My plan was to remove the existing doors, mount the hardware and have barn doors, opening up the bathroom space. The plan pretty much worked..
I purchased the 8 foot rail and extra door hangers. In the end an 8 foot rail with two, 2 foot doors fit almost perfectly. I live in townhouse. My studs are 13, 11 to 16, to half inches all throughout the wall. I used a stud finder, started marking and then started scratching my head. The rail for the hardware is pre-drilled at 16 inches apart. This leaves you no options, your screws have to go in the wall 16 inches apart, or install a header.
Keep in mind a header will set your door further off the wall. In hindsight, you could drill some new holes in the rail if you needed to also. Using the instructions, I had 80 inch doors, added the appropriate height, to include the rail and ran into a new problem.
The height of the rail was running right over my existing molding. I knew this was going to happen, and as I planned the molding solved my stud issue. This is because behind the molding should be the door frame with 2 by 4s behind the molding and drywall The door frame was 2 inches higher than the molding. My kid could have built this wall better. So this completely threw off the proper height of my door.
I had to bring it up in order to hit wood in the wall. Bringing the height up would later cause me another problem. As you can see, my plan was falling apart. Each problem and solution, created a new one.
So using a level, knowing I had a height that had wood behind it, I was able to somehow set all 6 screws into wood. Now, onto the hardware you mount to the door. The instructions say drill it 1. I had to bring the hole up or the door would be sitting on the floor. So I got the rail mounted, hardware wheels installed on the doors, moment of truth. Hung the door and the height was actually perfect. That little amount was acceptable for me, but was my last issue. I had to get a chisel and knock out a path in the molding so that the screws cleared it.
This was very annoying.. In the end though, it actually turned out almost exactly the way I envisioned. I have some finish work to do and some touch up paint to finish it up. Wait, one more issue. On the bottom of the door you need a router for the door guide. So my doors are just free floating with no guide. Hate to spend the money but it would solve my problem.
Advice to the designers. Pre-drill more holes in the rail. Installing a header is not always practical because of existing molding. Included in the kit are small black plastic caps that pop into the steel to cover the holes on the end of the rail, include more of these and drill more holes in the steel. Also, include more end cap nuts that screw into the door hanger bolt.
The end blocks on the rails that stop the doors from sliding off are a great design. Provide or sell something for two doors in the middle to meet. Right now, I close both doors and they can be off center and over travel. Of course they slide and can be corrected but something to stop the doors in the middle would be helpful. Overall, a very doable project given the hardware, but be warned you might have to problem solve a little. This is my 2nd hardware kit from Industrial By Design. Installed on my 2nd barn door in my new house.
It is great hardware and the customer service is top notch. I wish all companies were as customer driven as these folks are!! Everyone that sees my 2 barn doors loves the look of the hardware that I used. Look no further, this is an excellent product and company. Great quality, great instructional video. This was my first barn door install and everything worked perfectly. I installed another one a week after. No surprises, this kit is well put together.
Rolls extremely well, well packaged. This kit is perfect for a heavy barn door. It arrived in 2 days. The instructions were great, but the installation video was awesome to watch before assembly. It explained and showed how to put it together and install perfectly. I highly recommend this product! The instructions were super easy to follow and their customer service is fantastic!
Our studs were not the same width as the predrilled holes in the rail and the seller offered great advice to add a header board and then mount the rail to it. See photo for finished product! The finish is a perfect matte black.
Door, handle, and latch not included in package but inexpensive to buy separately found at Lowes. Project to replace two bi-fold doors in a 52" door opening. Actual door was 54" x 7' and made out of 2 wood for weight purposes. Most difficult task was making the door because the Hardware Kit was a breeze. This product arrived on time, in perfect condition, with great instructions both written and video. Couldn't be happier with the product or the end result.
HIGHLY recommend this product - it works smoothly and is exactly what we needed for our 4' wide x 8' tall door to function safely. See all reviews. See all customer images. Most recent customer reviews. Published 19 hours ago. Published 6 days ago. Published 11 days ago. Published 16 days ago.